Mobile App - Monitoring
The mobile application is the main tool for monitoring the XS4 Sense system. It allows you to view the status of each installed controller and sensor and to assess any corrective actions needed to optimize system performance.
Download XS4 Sense mobile application
 | iOS |
 | Android |
Login
Use your credentials to log in. Depending on the authorization level associated with your account, you can view the system, manage it, and commission new controllers with their corresponding sensors.
Mobile app login
Dashboard
Through the provided dashboard, it is possible to view an overview of the system's total energy consumption and savings. The filters allow you to define the data range to display, selecting a specific time period, a single room, or a group of rooms.
Mobile app dashboard
Monitor
The Monitor screen of the XS4 Sense mobile application allows viewing the real-time status of all rooms configured in the system. Each card represents a room identified by its number and displays the main operational information, including:
Occupancy status (person icon)
Door status (open or closed door icon)
Window status (open or closed window/balcony icon)
WiFi signal strength (red icon means the controller is not reachable)
Battery level alert (red icon means low battery level)
Possible warnings or communication errors
Blue cards indicate rooms that are occupied, while grey cards represent unoccupied rooms.
Mobile app monitor
Room detail
By clicking on a specific room, it is possible to view its detailed status and operational parameters. In the Main screen, the most relevant functions are displayed in a summarized way, while in the Room Details section, all information related to the XS4 Sense controller and its connected sensors is shown.
Main screen
In this section of the application, the overall health and operating status of each room are displayed in a clear and intuitive way.
Mobile app monitor single room
| Icon | Description |
|---|---|
| Person icon | The icon can have two states: blue when the room is occupied and grey when the room is unoccupied. |
| Wifi icon | The icon indicates the WiFi signal level with four states: high, medium, low, and no signal. When the no signal icon is displayed, it means the controller is offline. |
| Multisensor icon | Displays the motion status detected by the sensor and reports any low-battery alarms or registered but disconnected sensors. |
| Door icon | Displays the door status, open or closed and reports any low-battery alarms or registered but disconnected sensors. |
| Window icon | Displays the window/balcony status, (open or closed) and reports any low-battery alarms or registered but disconnected sensors. |
Room details
In this section of the application, the detailed status of the selected room is displayed along with all connected sensors. This section is useful for accurately checking the status of each sensor and the proper operation of the system.
Mobile app monitor single room
Use caution when navigating within this menu, as you may unintentionally modify the real-time behavior of the XS4 Sense Controller, its sensors, or the default settings defined during the commissioning.
XS4 Sense Dashboard details section
| Icon | Description |
|---|---|
| Check-in | Indicates the current status of the controller. A grey dot means check-out, a blue dot means check-in. The information is received either from a PMS system or from the webhook integration with Space. |
| Digital input 1 | Indicates the status of digital input 1. Grey dot input open, blue dot input closed. |
| Digital input 2 | Indicates the status of digital input 2. Grey dot input open, blue dot input closed. |
| Relay 1 State | Indicates the status of relay 1. Grey dot relay not activated, blue dot relay activated. Only Local Users with the Engineering role can override the settings. |
| Relay 2 State | Indicates the status of relay 2. Grey dot relay not activated, blue dot relay activated. Only Local Users with the Engineering role can override the settings. |
| Door status source | Indicates which source has been assigned to the door function, choosing between digital input 1/2, BLE sensor, or inRoomNode. Only Local Users with the Engineering role can modify the settings. |
| Window status source | Indicates which source has been assigned to the window function, choosing between digital input 1/2 or BLE sensor. Only Local Users with the Engineering role can modify the settings. |
| Energy saving mode | Indicates which status has been assigned, choosing between Enable or Disable. Only Local Users with the Engineering role can modify the settings. |
| Door status | Indicates the door status: blue dot door closed, grey dot door open. |
| Window/balcony status | Indicates the window status: blue dot window closed, grey dot window open. |
| Room occupancy | Indicates room occupancy status, obtained from the occupancy logic. Grey dot room not occupied, blue dot room occupied. Only Local Users with the Engineering role can override the settings. |
| Room tentatively unoccupied | Indicates the state where the room is considered potentially unoccupied. It is triggered when the preliminary occupation detection time expires and remains active until the end of the occupancy detection period. Grey dot status active, blue dot status inactive. |
| Motion | Indicates the motion detection status inside the room, based on the Multisensor. Grey dot no detection, blue dot detection. |
| Preliminary occupancy detection | Indicates the duration, in minutes, starting from the door close event until the room is set as tentatively unoccupied. Only Local Users with the Engineering role can modify the settings. |
| Occupancy detection | Indicates the duration started from door close event to set room as unoccupied in minutes [m]. Only Local Users with the Engineering role can modify the settings. |
| Balcony/window delay | Indicate the duration to trigger action from balcony/window open time in seconds [s]. Only Local Users with the Engineering role can modify the settings. |
| False occupancy check | Indicate the duration from the last motion event to decide room is unoccupied in hours [h]. Only Local Users with the Engineering role can modify the settings. |
| BLE device absence | Maximum time after which, if the system no longer receives information from the BLE devices, the device is considered unreachable and an alarm is triggered in [minutes]. Only Local Users with the Engineering role can modify the settings. |
| Multisensor Battery Low | The value in [millivolts] below which the battery is considered low. Only Local Users with the Engineering role can modify the settings. |
| Door sensor Battery Low | The value in [millivolts] below which the battery is considered low. Only Local Users with the Engineering role can modify the settings. |
| Input voltage | Indicates the value of the supply voltage input to the controller [Volt]. |
| Current | Indicates the value of the instantaneous current measured by the controller [Ampere]. |
| Instant power | Indicates the value of the instantaneous power measured by the controller [Watt]. |
inRoomNode
XS4 Sense Dashboard inRoomNode informations
| Function | Description |
|---|---|
| Connected | Connection status between the XS4 Sense controller and the inRoomNode. A green dot is shown when connected, and a grey dot when disconnected. |
| Door Status | Indicates the door status: grey icon door closed, red icon door open. |
| Communication with lock | Indicates the communication status between the electronic lock and the inRoomNode module. A green dot is shown when connected, and a grey dot when disconnected. |
| Privacy | Indicates the activation of the deadbolt by the guest. A green dot indicates it is active, a grey dot indicates it is inactive. |
| Passage mode | Status about the function set by Salto Space |
| Battery | Indicates the battery status of the electronic lock. If the icon is red, it means the battery level is low. |
| Emergency mode | Status about the function set by Salto Space |
| Door left open | Indicates an alarm situation where the door, after being properly opened, has been left open beyond the allowed time. |
| Intrusion alarm | Indicates that the door has been opened without an authorized sequence, either from the inside or through an unauthorized opening. |
| Last card key operation | Indicates the status of the last access, specifying whether it was made by a Guest or by Staff, and displays any unauthorized access attempt. |
Multisensor 1/2 details
XS4 Sense Dashboard multisensors informations
Each connected sensor communicates the following details, useful for diagnostics and maintenance.
| Function | Description |
|---|---|
| Online status | Indicates the connection status of the sensor with the controller. Green dot indicates connected, grey dot indicates not connected, yellow triangle indicates the sensor is registered but not reachable by the controller. |
| Motion | Indicates the status of the Multisensor in detecting presence in the room. Grey dot no presence, blue dot presence detected. |
| Sensibility | Indicates the level of sensitivity of PIR device LOW, MED, HIGH. The default value is HIGH. Only Local Users with the Engineering role can modify the settings. |
| Battery level | Indicates the battery charge value in millivolts [mVolt]. The icon turns red when the charge level falls below the threshold set in the configuration. |
| Ambient temperature | Indicates the temperature value measured by the Multisensor, expressed in degrees Celsius [°C]. |
| Temperature offset | Setting a temperature correction offset [°C]. Only Local Users with the Engineering role can modify the settings. |
| Ambient humidity | Indicates the humidity [%] value measured by the Multisensor. |
| TX power level | Indicates the transmission power value set in the sensor. Only Local Users with the Engineering role can modify the settings. |
| Signal level | Indicates the BLE signal value received by the sensor. |
Door 1 / Window 1 to 3 details
XS4 Sense Dashboard door/window informations
Each connected sensor communicates the following details, useful for diagnostics and maintenance.
| Function | Description |
|---|---|
| Online status | Indicates the connection status of the sensor with the controller. Green dot indicates connected, grey dot indicates not connected, yellow triangle indicates the sensor is registered but not reachable by the controller. |
| Open/Close | Indicates the door or window opening status. |
| Battery level | Indicates the battery charge value in millivolts [mVolt]. The icon turns red when the charge level falls below the threshold set in the configuration. |
| TX power level | Indicates the transmission power value set in the sensor. Only Local Users with the Engineering role can modify the settings. |
| Signal level | Indicates the BLE signal value received by the sensor. |
Use caution when navigating within this menu, as you may unintentionally modify the real-time behavior of the XS4 Sense Controller, its sensors, or the default settings defined during the commissioning.